Installation of lighting for stretch ceiling. Lenka mortgages
For the organization of competent lighting in the stretch ceiling use lamps with tungsten filament, fluorescent or halogen. If you plan on their normal setting (no heat ring), it should be limited to incandescent lamps with a power of 50 W fluorescent or halogen and with a power of less than 35 watts. If you want to install more striking instruments we need to equip them with additional insulation so that the blade does not overheat and does not SAG.
There are several models of lamps designed specifically for use on suspended ceilings. The first type of steel lamps that are injected in the ceiling. With their help it is possible to achieve spot lighting of objects in the room and its various sections. The maximum power of the bulb is 50W. In addition, there is a special model with water protection.
Another model is the so – called cardan lamp, for which you can adjust the position of the reflector in the vertical and horizontal planes. Due to this light is directed to the desired point of the room.
Preparation.
The mounting points of the lamps are laid out on the ceiling, they are fed wire. At a basic ceiling mounted racks for lamps.
The wiring is held to the mounting of spotlights and chandeliers. Then install the brackets, special fasteners under the lights and under the chandelier.
Installation of lighting fixtures produce ceiling mounted, fittings or special mounting element.
In the right place ceiling cut, paste over the holes on the perimeter of a special ring, make the issue of electrical wiring, plug in the lamp.
As is known, installation of lighting fixtures produced in the last stage of the installation of stretch ceiling.
On the canvas in the place of attachment of the lamp are glued plastic ring. They will not give the material a break. After stretching the fabric on the outside through the holes of the uprights will be attached to your chosen lamps.
Installation.
1. To install the built-in lamp, the ceiling is applied with special profile round shape in the place where before the installation of the ceiling was set stand for the lamp.
2. The profile adheres strictly under the counter.
3. Then, the part of the canvas, with which the profile was glued to the front, cut along the contour of its inner surface.
4. Then through the resulting hole "pulled out" wiring of the future lamp, and the hole is enclosed with a decorative profile.
5. Then follows the installation of the lamp. Before connecting the lamp to the body is put on one or more insulating rings.
6. The final operation is the adjustment of the set lamp according to the level of the stretched ceiling. It's quite easy because everything is visible to the eye. It only remains to screw in a light bulb and enjoy the result.
It is not recommended to mount a large number of built-in fixtures – there are certain constraints on power and temperature heating.
Also among popular spotlights waterproof, they can be installed in bathroom, swimming pool, sauna and other rooms with high humidity.
These lamps are protected by glass and silicone gaskets, they do not permit the entry of fumes and water into the lamp. If you want to save on electricity and use low-power lamps, will put the transformer behind the suspended ceiling. Some designs of spotlights allow you to "play with light", ie to direct the luminous fluxes in different directions and create interesting effects in the interior.
If a suspended ceiling is already installed, you can put the overhead lights. They are more economical and universal, easy fit for apartments. Similarly to the home environment more suitable for elegant lighting pendant, lighting rods, sconces. Overhead lights are also just attached to the suspended ceiling, only need to take into account a certain distance from the lamp to the surface
For the organization of competent lighting in the stretch ceiling use lamps with tungsten filament, fluorescent or halogen. If you plan on their normal setting (no heat ring), it should be limited to incandescent lamps with a power of 50 W fluorescent or halogen and with a power of less than 35 watts. If you want to install more striking instruments we need to equip them with additional insulation so that the blade does not overheat and does not SAG.
There are several models of lamps designed specifically for use on suspended ceilings. The first type of steel lamps that are injected in the ceiling. With their help it is possible to achieve spot lighting of objects in the room and its various sections. The maximum power of the bulb is 50W. In addition, there is a special model with water protection.
Another model is the so – called cardan lamp, for which you can adjust the position of the reflector in the vertical and horizontal planes. Due to this light is directed to the desired point of the room.
Preparation.
The mounting points of the lamps are laid out on the ceiling, they are fed wire. At a basic ceiling mounted racks for lamps.
The wiring is held to the mounting of spotlights and chandeliers. Then install the brackets, special fasteners under the lights and under the chandelier.
Installation of lighting fixtures produce ceiling mounted, fittings or special mounting element.
In the right place ceiling cut, paste over the holes on the perimeter of a special ring, make the issue of electrical wiring, plug in the lamp.
As is known, installation of lighting fixtures produced in the last stage of the installation of stretch ceiling.
On the canvas in the place of attachment of the lamp are glued plastic ring. They will not give the material a break. After stretching the fabric on the outside through the holes of the uprights will be attached to your chosen lamps.
Installation.
1. To install the built-in lamp, the ceiling is applied with special profile round shape in the place where before the installation of the ceiling was set stand for the lamp.
2. The profile adheres strictly under the counter.
3. Then, the part of the canvas, with which the profile was glued to the front, cut along the contour of its inner surface.
4. Then through the resulting hole "pulled out" wiring of the future lamp, and the hole is enclosed with a decorative profile.
5. Then follows the installation of the lamp. Before connecting the lamp to the body is put on one or more insulating rings.
6. The final operation is the adjustment of the set lamp according to the level of the stretched ceiling. It's quite easy because everything is visible to the eye. It only remains to screw in a light bulb and enjoy the result.
It is not recommended to mount a large number of built-in fixtures – there are certain constraints on power and temperature heating.
Also among popular spotlights waterproof, they can be installed in bathroom, swimming pool, sauna and other rooms with high humidity.
These lamps are protected by glass and silicone gaskets, they do not permit the entry of fumes and water into the lamp. If you want to save on electricity and use low-power lamps, will put the transformer behind the suspended ceiling. Some designs of spotlights allow you to "play with light", ie to direct the luminous fluxes in different directions and create interesting effects in the interior.
If a suspended ceiling is already installed, you can put the overhead lights. They are more economical and universal, easy fit for apartments. Similarly to the home environment more suitable for elegant lighting pendant, lighting rods, sconces. Overhead lights are also just attached to the suspended ceiling, only need to take into account a certain distance from the lamp to the surface
Комментариев нет:
Отправить комментарий